specifications subject to change without notice. please check our website for latest information. chip inductors C 1008ls series (2520) document 103-1 document 103-1 revised 12/18/02 inductance 2 percent srf min 5 dcr max 6 i rms 7 part number 1 (h) tolerance 3 q min 4 (mhz) (ohms) (ma) 1008ls-122x_b_ 1.2 @ 7.9mhz 10, 5 48 @ 50 mhz 210 0.68 650 1008ls-152x_b_ 1.5 @ 7.9mhz 10, 5 41 @ 50 mhz 190 0.76 630 1008ls-182x_b_ 1.8 @ 7.9mhz 10, 5 39 @ 50 mhz 170 0.84 600 1008ls-222x_b_ 2.2 @ 7.9mhz 10, 5 34 @ 50 mhz 150 1.10 520 1008ls-272x_b_ 2.7 @ 7.9mhz 10, 5 34 @ 50 mhz 135 1.28 490 1008ls-332x_b_ 3.3 @ 7.9mhz 10, 5 32 @ 50 mhz 120 1.46 450 1008ls-392x_b_ 3.9 @ 7.9mhz 10, 5 32 @ 7.9 mhz 105 1.56 420 1008ls-472x_b_ 4.7 @ 7.9mhz 10, 5 31 @ 7.9 mhz 90 1.68 400 1008ls-562x_b_ 5.6 @ 7.9mhz 10, 5 31 @ 7.9 mhz 80 1.82 380 1008ls-682x_b_ 6.8 @ 7.9mhz 10, 5 31 @ 7.9 mhz 70 2.00 360 1008ls-822x_b_ 8.2 @ 7.9mhz 10, 5 23 @ 7.9 mhz 65 2.65 330 1008ls-103x_b_ 10.0 @ 7.9mhz 10, 5 31 @ 7.9 mhz 60 2.95 300 these ferrite core surface mount inductors have lower dcr and higher current ratings than our 1008cs series. they?re available with inductance values from 1.2 to 10 h. coilcraft designer?s kit c136 contains samples of all 5% inductance tolerance parts. to order, contact coilcraft or visit http://order.coilcraft.com to order on-line. 2. inductance measured using coilcraft smd-a fixture in an agilent/ hp 4286a impedance analyzer with coilcraft-provided correlation pieces. 3. tolerances in bold are stocked for immediate shipment. 4. q measured using an agilent/hp 4291a with an agilent/hp 16193 test fixture. 5. srf measured using an agilent/hp 8753d network analyzer with a coilcraft smd-d fixture. 6. dcr measured on a cambridge technology micro-ohmmeter. 7. average current for 15c temperature rise from 25c. 8. operating temperature range ? 40c to +85c. 9. electrical specifications at 25c. see qualification standards section for environmental and test data. for part marking data see color coding section. 1. when ordering, please specify tolerance and packaging codes: 1008ls-103x j b c tolerance: j =5% k = 10% (table shows stock tolerances in bold.) packaging: c =7 machine-ready reel. eia-481 embossed plastic tape (2000 parts per full reel). b = less than full reel. in tape, but not machine ready. to have a leader and trailer added ($25 charge), use code letter c instead. d =13 machine-ready reel. eia-481 embossed plastic tape. factory order only, not stocked (7500 parts per full reel).
1008ls series (2520) specifications subject to change without notice. please check our website for latest information. document 103-2 document 103-2 revised 12/14/04 typical q vs frequency typical l vs frequency a max b max c max d ref e f g h i j 0.115 0.110 0.080 0.020 0.080 0.020 0.060 0.100 0.040 0.050 2,92 2,79 2,03 0,51 2,03 0,51 1,52 2,54 1,02 1,27 a b overall f i i g d e terminal f j c h terminal wraparound: approx 0.015/0,38 both ends recommended land pattern 0 2 4 6 8 10 1 10 100 1000 frequency (mhz) inductance (uh) 1.8 h 2.2 h 3.3 h 6.8 h 0 10 20 30 40 50 1 10 100 1000 frequency (mhz) q factor 1.8 h 2.2 h 3.3 h 6.8 h weight: 38.3 ? 41.0 mg terminations: platinum/palladium/silver tape and reel: 2000/7 reel; 7500/13 reel 8 mm tape width for packaging data see tape and reel specifications section.
|
